Viega Eco Plus WC element
Product information
Viega Eco Plus WC element
Viega Eco Plus
| Year built (from): | 01.08.2011 |
Trade mark rights exist for this document; for further information, go to viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and sanitary professionals and trained personnel
SHK-FachkräfteDrywall builder
Individuals without the abovementioned training or qualification are not permitted to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
INFO!
This symbol gives additional information and hints.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e. g. EN) and/or in Germany (e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Standards and regulations
The following standards and regulations apply to Germany / Europe. National regulations can be found on the relevant web site of your country at viega.com/standards .
Regulations from section: Sound protection
Product description
Overview
The WC element is equipped as follows:
- 1 - Viega Eco Plus WC element
- 2 - threaded rods for fixing sanitary objects (gauges for bore hole 180 or 230 mm)
- 3 - adjustable feet
- 4 - drain elbow
- 5 - fixing height for the WC ceramic 330 mm
- 6 - Viega concealed cistern 1F
- 7 - marking 1.0 m above the upper edge of the finished floor
- 8 - fixing set (not included in the scope of delivery model 8173)
- 9 - flush actuation site protection
Compatible components
The WC element is compatible with all common WC ceramics, even with larger projection (barrier-free).
The WC element can be extended by the following compatible components:
fixing element (model 8169.2)
Fixing element
The fixing element is suitable for barrier-free installation. Supports and handles can be mounted on the fixing element. The construction height of the fixing element is 1130 mm.
Compatible flush plates
Product |
|---|
Standard |
Visign for Style |
Visign for More |
Visign for Care sensitive |
Visign for More sensitive |
Visign for Public |
Technical data
Flush volume
Small flush volume |
|---|
Large flush volume |
Handling
Assembly information
Mounting conditions
Suitable walls
The WC element can be mounted on the following walls:
masonry walls
concreted walls
metal support profile
The WC element may only be mounted on even wall surfaces.
Construction height
With the construction height, the marked height of the upper edge of the finished floor must be observed.
Installation depth
The installation depth can be between 85 mm and 200 mm.
WC ceramic
The WC element can only be used in combination with wall-hung WCs (fixing gauges for bore hole 180 mm or 230 mm).
Actuation
The WC element can be extended by a remote actuation Visign for Public1 (model 8326.21) or by an electronic actuation (model 8350.33), as well as by sensitive flush plates (model 8352.21, 8352.11 and 8355.11). The corresponding actuation method must be prepared before the WC element is clad and tiled.
The corresponding empty pipe (included in the scope of delivery of the remote actuation) is required when preparing the remote actuation Visign for Public1.
Installation dimensions
Dimensions
Required tools
The following tools are required for mounting the WC element:
drill with 10 mm drill bit
ratchet with sockets: 13 mm / 17 mm
fork or ring spanner: 13 mm / 17 mm / 19 mm
Assembly
Mounting WC element
INFO!
Masonry and concreted walls
You should use a support bracket (model 8165) when mounting multiple WC elements with an interval of > 490 mm. Observe the instructions for use of the support bracket when mounting.
Masonry wall
Mounting with fixing set (model 8173)
-
Determine and mark fixing points.
X1: 390 mm (model 8180.73)
X2: 440 mm (model 8173)
X3: At a construction height of 1130 mm, the size is 1110 mm.
-
Drill holes.
-
Mount the fixing set with the fork spanner (size 13).
-
Align the height (size 17) of the WC element in accordance with the cutting check.
-
Attach WC element to the floor using the fork spanner (size 13) and the screws and dowels supplied.
-
Align WC element.
-
Set the installation depth of the pre-wall element (85–200 mm) with the fork spanner (size 17).
-
Attach WC element to the wall.
-
Double-clad WC element with IFGP cladding panels (model 8055.10) (2 x 12.5 mm).
Mounting with fixing set (model 8180.73)
-
Determine and mark fixing points.
X1: 390 mm (model 8180.73)
X2: 440 mm (model 8173)
X3: 1110 mm.
-
Drill holes.
-
Mount the fixing set with the fork spanner (size 17).
-
Align the height (size 17) of the WC element in accordance with the cutting check.
-
Attach WC element to the floor using the fork spanner (size 13) and the screws and dowels supplied.
-
Align WC element.
-
Set the installation depth of the pre-wall element (130–200 mm) with the fork spanner (size 17).
-
Attach WC element to the wall.
-
Double-clad WC element with IFGP cladding panels (model 8055.10) (2 x 12.5 mm).
On-site stud frame
-
If necessary, adjust (pre-mounted) foot depth from 75 mm to 50 mm.
-
Pull the foot out and turn by 90°.
-
Determine construction height in accordance with the on-site marking of the upper edge of the finished floor.
-
Pull WC element up (cutting check) and align.
-
Mark holes for floor supports and drill.
-
Tighten feet with the fork spanner (size 17).
-
Attach WC element to the stud frame using the screws supplied.
-
Optional:
Viega Eco Plus fixing element model 8169.2.
-
Double-clad WC element with IFGP cladding panels (model 8055.10) (2 x 12.5 mm).
Preparing optional actuation versions
Prepare remote actuation
The corresponding empty pipe (included in the scope of delivery of the remote actuation) is required when preparing the remote actuation Visign for Public1 (model 8326.21).
-
Lead the empty pipe from the hollow wall socket into the concealed cistern.
Distance from the remote actuation to the cistern (x)
min. 1.0 m
max. 1.7 m
Prepare electrical actuation
-
Lead empty pipe from the switch or button into the concealed cistern, to connect the concealed socket and concealed cistern.
Positioning of the cistern power pack
X1= max. 0.75 m
X2= max. 2.75 m with an extension cable, 1 x article number 628 505
X3= max. 4.75 m with two extension cables, 2 x article number 628 505
Setting the flush volume
INFO!
Immediate re-flushing of the flush volume is possible at the factory settings.
Small flush volume
The WC element is factory-set at a small flush of approx. 3 l. The small flush volume can be set from approx. 3 l to approx 2.5 l.
-
Remove the drain valve from the concealed cistern.
-
Push the slide control on the side of the overflow pipe to the desired small flush volume:
Top position: approx. 2.5 l
Bottom position: approx. 3 l
Large flush volume
The WC element is factory-set at a large flush volume of approx. 4.5 l. The large flush volume can be set to approx. 6 l.
-
Remove the drain valve from the concealed cistern.
-
Push the slide control below the drain valve to the desired large flush volume:
left: approx. 4.5 l
right: approx. 6 l
Removing filling valve
-
Remove cover.
-
Loosen locking device the mechanism.
-
Remove bow of the mechanism from the drain valve.
-
Remove mechanism out the front.
-
Push the holder of the restrainer together.
-
Remove restrainer upwards.
-
Remove the restrainer towards the front.
-
Close open corner valve.
-
Separate the flexible hose from the corner valve at the union nut (SW 19).
-
Release the filling valve holder from the bracket.
-
Remove filling valve from the revision opening in a horizontal position.
Cleaning and maintenance
Cleaning may only be carried out by specialist trade professionals or qualified experts.
Cleaning and maintenance of the concealed cistern
The concealed cistern is constantly under mechanical, chemical, and physical stress. For this reason, the components must be cleaned as required, and the drain and filling valve seals renewed.
In areas or regions with hard water due to high concentration of calcium or magnesium salts, there is the risk of limescale deposits developing on the inlet and drain valves. The valves may have to be replaced, depending on the extent of the deposits.
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.